# X Bar R Control Charts (2023)

## What are X Bar R Control Charts?

X Bar R charts are the widely used control chart for variable data to examine the process stability in many industries (like Hospital patients’ blood pressure over time, customer call handle time, length of the part in production process etc.,).

Selection of appropriate control chart is very important in control charts mapping, otherwise ended up with inaccurate control limits for the data.

X bar R chart is used to monitor the process performance of a continuous data and the data to be collected in subgroups at a set time periods. It is actually a two plots to monitor the process mean and the process variation over the time and is an example ofstatistical process control. These combination charts helps to understand the stability of processes and also detects the presence ofspecial cause variation.

The cumulative sum (CUSUM) and the exponentially weighted moving average (EWMA) charts are also monitors the mean of the process, but the basic difference is unlike X bar chart they consider the previous value means at each point.

## X Bar R Control Chart Definitions

X-bar chart: The mean or average change in process over time from subgroup values. The control limits on the X-Bar brings the sample’s mean and center into consideration.

R-chart: The range of the process over the time from subgroups values. This monitors the spread of the process over the time.

## Use X Bar R Control Charts When:

• Even very stable process may have some minor variations, which will cause the process instability. X bar R chart will help to identify the process variation over the time
• When the data is assumed to benormally distributed.
• X bar R chart is for subgroup size more than one (forI-MR chartthe subgroup size is one only) and generally it is used when rationally collect measurements in subgroup size is between two and 10 observations.
• The X Bar S Control chartare to be consider when the subgroup size is more than 10.
• When the collected data is in continuous (ie Length, Weight) etc. and captures in time order

## How to Interpret the X Bar R Control Charts

• To correctly interpret X bar R chart, always examine the R chart first.
• The X bar chart control limits are derived from the R bar (average range) values, if the values are out of control in R chart that means the X bar chart control limits are not accurate.
• If the points are out of control in R chart, then stop the process. Identify the special cause and address the issue. Remove those subgroups from the calculations.
• Once the R bar chart is in control, then review X bar chart and interpret the points against the control limits.
• All the points to be interpret against the control limits but not specification limits. As specification limits are provided by customer or management whereas control limits are derived from the average and range values of the subgroups.
• If any point out of control in X bar chat. Identify the special cause and address the issue.
• Process capability studies can be performed only after both X bar and R chart values are within the control limits. There is no meaning to perform process capability studies of an unstable process.

## Steps to follow for X bar R chart

### Objective of the chart and subgroup size

• Determine the objective of the chart and choose the important variables
• Choose the appropriate subgroup size and the sampling frequency
• Collect minimum 20 to 25 sets of samples in the time sequence

Example: In a manufacturing industry the plate thickness is one of the important CTQ factor, during Measure phase, project team performed the process capability study and identified that the process is not capable(less than 2 sigma). In Analyze phase collected 20 sets of plate thickness samples with a subgroup size of 4.

(Video) CONTROL CHART BASICS and the X-BAR AND R CHART +++++ EXAMPLE

### Compute X bar and R values

• Measure the average of each subgroup i.e X bar, then compute grand average of all X bar value, this will be center line for X bar chart
• Compute the range of each subgroup i.e Range, then measure grand averages of all range values ie R bar and this will be the center line for R chart

### Determine the Control Limits

• The first set of subgroups are to determine the process mean and standard deviation, these values are to be consider for creation of control limits for both range and mean of each subgroup
• The process to be in control in the early phase of the production. Special causes to be identified if any of the points are out of control during initial phase and also the subgroup has to be removed for calculation.
• Sometimes in the initial phase it would be also good to have few points out of control on the x-bar portion. Otherwise, if all the values are within the control limits may be because of slop in the measurement system, team won’t focus on it. Identify appropriate Measurement System Evaluation (MSE).
• Where
• X is the individual value (data)
• n is the sample size (subgroup size)
• X bar is the average of reading in a sample
• R is the Range, in other words the difference between largest and smallest value in each sample
• R bar is the average of all the ranges.
• UCL is Upper control limit
• LCL is Lower control limit

The below control chart constants are approximate values to measure the control limits for X bar R chart and other control charts based on subgroup size

Refer common factors for various control charts

Example cont: In the above example n=4

### Interpret X bar and R chart

• Plot both X bar and R chart and identify the assignable causes

Example Cont: Use the above values and plot the X bar and Range chart

(Video) XBar-R Control Charts

From the both X bar and R charts it isclearly evident that most of the values are out of control, hence the processis not stable

### Monitor the process after improvement

• Once the process stabilizes and control limits are in place, monitor the process performance over the time.

Example cont: Control Phase- Once the process is improved and matured, team identified the X bar R chart is one the control method in Control plan to monitor the process performance over the time period

Following are the measurement values in Control phase of the project

Compute X bar and Range

From the both X bar and R charts it is clearly evident that the process is almost stable. During initial phase one value is out of control, team has to perform the root cause analysis for the special cause and also the process is smoothing out from the data set number 16. If that continued, the chart would need new control limits from that point.

(Video) Quality Control Part 2 (Control Charts for Variables X bar and R bar charts)

• After the process stabilized, still if any point going out of control limits, it indicates an assignable cause exists in the process that needs to be addressed. This is an ongoing process to monitor the process performance.

## Important notes

• A process is “in control” that indicates means of the process is stable and it can be predictable
• A process is in stable that does not mean it’s a zero defect process.
• Remember to NEVER put specifications on any kind ofcontrol chart.
• The points on the chart are comprised of averages, not individuals. Specification limits are based on individuals, not averages.
• The operator might have the tendency to not react to a point out control when the point is within the specification limits.
• X bar R chart helps to avoid unnecessary adjustments in the process

## X Bar R Control Chart Videos

• Ted Hessing

(Video) Statistical Process Control | Chart for Means (x-bar chart)

I originally created SixSigmaStudyGuide.com to help me prepare for my own Black belt exams. Overtime I've grown the site to help tens of thousands of Six Sigma belt candidates prepare for their Green Belt & Black Belt exams. Go here to learn how to pass your Six Sigma exam the 1st time through!

View all posts

• Ramana PV

View all posts

## FAQs

### How do you interpret an X bar and R control chart? ›

The X-bar chart shows how the mean or average changes over time and the R chart shows how the range of the subgroups changes over time. It is also used to monitor the effects of process improvement theories. As the standard, the X-bar and R chart will work in place of the X-bar and s or median and R chart.

How do you solve an X-bar chart? ›

Calculate the X-bar Chart Lower Control Limit, or lower natural process limit, for the X-bar chart by multiplying R-bar by the appropriate A2 factor (based on subgroup size) and subtracting that value from the average (X-bar- bar). LCL(X-bar) = X-bar-bar - (A2 x R-bar) Plot the Lower Control Limit on the X-bar chart.

Why do we need to use both X bar and R charts together why can't we use one or the other? ›

Manufacturers typically use the X-bar and R-chart pair to visualize continuous data. The X-bar helps to monitor the average or the mean of the process and how this changed over time. The R-chart shows the sample range, which represents the difference between the highest and lowest value in each sample.

What does it mean if points fall outside the control limits of X Bar or R bar charts What does this suggest? ›

If you are looking at a chart pair (X-bar and R, X-bar and s, or X and MR), look at both charts. Points falling outside the control limits may be the result of a special cause that was corrected quickly, either intentionally or unintentionally. It may also point to an intermittent problem.

What is an XBAR R chart used for? ›

An Xbar-R chart is a quality control chart used to plot subgroup means and ranges of individual values from a single characteristic on a given part that were all produced on the same machine. A traditional Xbar-R chart is a single stream of data for a unique Part/Process/Test combination.

How do you interpret bar chart results? ›

Interpret the key results for Bar Chart
1. Step 1: Compare groups. Look for differences in the heights of the bars. The bars show the values for the groups. ...
2. Step 2: Compare groups within groups. Compare bars within the clusters or stacks to understand the proportions of subcategories within each main group.

How do you calculate R bar? ›

Compute X bar and R values
1. Measure the average of each subgroup i.e X bar, then compute grand average of all X bar value, this will be center line for X bar chart.
2. Compute the range of each subgroup i.e Range, then measure grand averages of all range values ie R bar and this will be the center line for R chart.

## Videos

1. Xbar-R and Xbar-s chart: Detailed illustration with Practical Examples
(LEARN & APPLY : Lean and Six Sigma)
2. Create Control Charts (X-Bar & R Chart) in Excel
(Quality HUB India)
3. Building Control Charts (Xbar and R Chart) in Microsoft Excel
(Vafa Saboori)
4. Part 1- Control Charts: X-bar chart, R-chart, & I-MR chart | Statistical Process Control
(RealEngineeringExplained)
5. Xbar & R Control Chart in Microsoft Excel [Excel SPC]
(The Engineering Toolbox Channel)
6. Control Charts - The X Bar R chart the manual way....a true 6 Sigma skill
(Paul Allen)
Top Articles
Latest Posts
Article information

Author: Ouida Strosin DO

Last Updated: 04/01/2023

Views: 5470

Rating: 4.6 / 5 (56 voted)

Author information

Name: Ouida Strosin DO

Birthday: 1995-04-27